New application of bimetallic Ag/Pt nanoplates in a colorimetric biosensor for specific detection of E. coli in water

• Azam Bagheri Pebdeni,
• Mohammad N. AL-Baiati and
• Morteza Hosseini

Beilstein J. Nanotechnol. 2024, 15, 95–103, doi:10.3762/bjnano.15.9

• microscopy (FE-SEM) was used to investigate the form and shapes of NPLs. The size of the NPLs is approx. 42 nm. Figure 1a shows a combination of truncated triangular and circular plates of Ag/Pt NPLs. The NPLs were evenly distributed and shaped in the form of discs or triangles. Energy-dispersive X-ray

• spectroscopy (EDS) was used to examine Ag and Pt on the synthesized NPLs (Figure 1b). The percentage of Pt is smaller than that of Ag, indicating that a thin layer of Pt ions has been coated on the surface of Ag NPLs. In the aqueous solution, the Ag/Pt NPLs appear bluish purple. To predict the secondary

Influence of conductive carbon and MnCo₂O₄ on morphological and electrical properties of hydrogels for electrochemical energy conversion

• Sylwia Pawłowska,
• Karolina Cysewska,
• Yasamin Ziai,
• Jakub Karczewski,
• Piotr Jasiński and
• Sebastian Molin

Beilstein J. Nanotechnol. 2024, 15, 57–70, doi:10.3762/bjnano.15.6

• influence of porosity and conductive properties of these composites on the electrochemical activity of catalyst particles in OER. Elemental mapping by energy-dispersive X-ray spectroscopy (EDS) confirmed the presence of MCO particles inside the hydrogel structure (Figure 2 and Supporting Information File 1

Sulfur nanocomposites with insecticidal effect for the control of Bactericera cockerelli

• Lany S. Araujo-Yépez,
• Juan O. Tigrero-Salas,
• Vicente A. Delgado-Rodríguez,
• Vladimir A. Aguirre-Yela and
• Josué N. Villota-Méndez

Beilstein J. Nanotechnol. 2023, 14, 1106–1115, doi:10.3762/bjnano.14.91

• rosemary essential oils with the three concentrations of 0.25%, 0.5%, and 0.75%. The samples were characterized by UV–visible spectroscopy, energy-dispersive X-ray spectroscopy, transmission electron microscopy, and scanning electron microscopy. The insecticidal efficacy of the nanocomposites was evaluated

• eucalyptus and rosemary at different concentrations. Characterizations were carried out through UV–visible spectroscopy, energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), and scanning electron microscopy (SEM); also the insecticidal efficacy of the NCMPs for the control of

• stabilizing agent. Characterization techniques and equipment UV–visible spectroscopy was performed on an Analytik Jena SPECORD® S 600 spectrophotometer. Size and morphology of the SNPs were determined using an FEI Tecnai G2 Spirit Twin transmission electron microscope. Energy-dispersive X-ray spectroscopy

Properties of tin oxide films grown by atomic layer deposition from tin tetraiodide and ozone

• Kristjan Kalam,
• Peeter Ritslaid,
• Tanel Käämbre,
• Aile Tamm and
• Kaupo Kukli

Beilstein J. Nanotechnol. 2023, 14, 1085–1092, doi:10.3762/bjnano.14.89

• ]. The SnO2 films grown at 300 and 500 °C, that is, those with low residual iodine content, were analysed ex situ in terms of surface chemistry using soft X-ray spectroscopy methods. The Sn 3d XPS data (Figure 10a) show almost identical spectra for the samples deposited at 300 and 500 °C, and the narrow

Experimental investigation of usage of POE lubricants with Al₂O₃, graphene or CNT nanoparticles in a refrigeration compressor

• Kayhan Dağıdır and
• Kemal Bilen

Beilstein J. Nanotechnol. 2023, 14, 1041–1058, doi:10.3762/bjnano.14.86

• nanoparticles is presented separately in the subsequent sections to verify the catalog information provided by the manufacturer. In the characterization of the nanoparticles used in the study, field-emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction

A visible-light photodetector based on heterojunctions between CuO nanoparticles and ZnO nanorods

• Doan Nhat Giang,
• Nhat Minh Nguyen,
• Duc Anh Ngo,
• Thanh Trang Tran,
• Le Thai Duy,
• Cong Khanh Tran,
• Thi Thanh Van Tran,
• Phan Phuong Ha La and
• Vinh Quang Dang

Beilstein J. Nanotechnol. 2023, 14, 1018–1027, doi:10.3762/bjnano.14.84

• . The energy-dispersive X-ray spectroscopy (EDS) results in Figure 1c show Zn, Cu, and O, which indicates the presence of ZnO and CuO. No further impurities were found. The results from X-ray diffractometry (XRD) and UV–vis absorption spectroscopy confirm that the nanoparticles covering the surfaces and

Green SPIONs as a novel highly selective treatment for leishmaniasis: an in vitro study against Leishmania amazonensis intracellular amastigotes

• Brunno R. F. Verçoza,
• Robson R. Bernardo,
• Luiz Augusto S. de Oliveira and
• Juliany C. F. Rodrigues

Beilstein J. Nanotechnol. 2023, 14, 893–903, doi:10.3762/bjnano.14.73

• , arrowheads). The ferrous nature of the observed structures was assessed by chemical element mapping analysis using energy-dispersive X-ray spectroscopy (Figure 2C), confirming that the electron-lucent structures contain iron atoms (Figure 2D). Transmission electron microscopy (TEM) was used to confirm the

• 20 kV equipped with an OXFORD X-MaxN 20 mm2 detector (Oxford Instruments, United Kingdom) for energy-dispersive X-ray spectroscopy. For transmission electron microscopy, after fixation, samples were dehydrated in increasing acetone concentrations and embedded in Epon. Ultrathin sections were obtained

N-Heterocyclic carbene-based gold etchants

• Robert B. Chevalier,
• Justin Pantano,
• Matthew K. Kiesewetter and
• Jason R. Dwyer

Beilstein J. Nanotechnol. 2023, 14, 865–871, doi:10.3762/bjnano.14.71

• dissolution of gold. We present scanning electron micrographs and elemental imaging analyses by energy dispersive X-ray spectroscopy to examine the effect of solutions of each species on the gold film. This work highlights the risk of unwanted etching during some routes to NHC-based surface functionalization

• % nitrogen gas. Electron micrographs were recorded using the SE2 detector of a Zeiss SIGMA VP field emission scanning electron microscope (SEM). Energy dispersive X-ray spectroscopy (EDS) spectra were obtained for each sample using an Oxford Instruments X-max 50 mm2 EDS attachment. Peaks were identified

Silver-based SERS substrates fabricated using a 3D printed microfluidic device

• Phommachith Sonexai,
• Minh Van Nguyen,
• Bui The Huy and
• Yong-Ill Lee

Beilstein J. Nanotechnol. 2023, 14, 793–803, doi:10.3762/bjnano.14.65

• NPs. The SEM image of PS@Ag reveals the presence of nanoscale gaps between the Ag NPs, which act as hot spots with a high electric field intensity when exposed to laser irradiation (Figure S10c). To confirm the distribution of chemical elements on the SERS substrate, energy-dispersive X-ray

• spectroscopy (EDS) was carried out, as illustrated in Figure S11 (Supporting Information File 1). The EDS mapping results indicate the uniformly distributed signal of the silicon wafer, while oxygen and silver are discontinuously distributed because of the space between PS and Ag NPs on the PS@Ag substrate

Carboxylic acids and light interact to affect nanoceria stability and dissolution in acidic aqueous environments

• Matthew L. Hancock,
• Eric A. Grulke and
• Robert A. Yokel

Beilstein J. Nanotechnol. 2023, 14, 762–780, doi:10.3762/bjnano.14.63

• produced drastically different TEM images, as expected from the DLS results. The number of nanoceria particles exposed to citric acid was reduced between weeks 0 and 1. By week 2, most of the particles completely disappeared with no evidence of cerium determined by energy-dispersive X-ray spectroscopy (EDS

Titania nanoparticles for photocatalytic degradation of ethanol under simulated solar light

• Evghenii Goncearenco,
• Iuliana P. Morjan,
• Claudiu Teodor Fleaca,
• Florian Dumitrache,
• Elena Dutu,
• Monica Scarisoreanu,
• Valentin Serban Teodorescu,
• Alexandra Sandulescu,
• Crina Anastasescu and
• Ioan Balint

Beilstein J. Nanotechnol. 2023, 14, 616–630, doi:10.3762/bjnano.14.51

• pyrolysis from TiCl4 vapor in air in the presence of ethylene as sensitizer at different working pressures (250–850 mbar) with and without further calcination at 450 °C. The obtained powders were analyzed by energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, X-ray diffractometry, and

• described as: The raw TiO2 powders contain some carbon (from the decomposition of the ethylene sensitizer) and chlorine impurities, whose amount it is greatly diminished by calcination in air at 450 °C for 5 h. To certify this, a composition investigation by energy-dispersive X-ray spectroscopy (EDS) has

Nanoarchitectonics to entrap living cells in silica-based systems: encapsulations with yolk–shell and sepiolite nanomaterials

• Celia Martín-Morales,
• Jorge Fernández-Méndez,
• Pilar Aranda and
• Eduardo Ruiz-Hitzky

Beilstein J. Nanotechnol. 2023, 14, 522–534, doi:10.3762/bjnano.14.43

• without staining. Electron microscopy imaging was conducted using a field-emission scanning electron microscope FEI-NOVA NanoSEM 230 equipped with an Apollo XL silicon drift detector from EDAX-Ametek or using a high-resolution JEOL IT500HR/LA microscope equipped with an energy dispersive X-ray

• spectroscopy (EDS) detector. In certain studies, samples were cut after immersing the beads, films, or foams in liquid N2 to obtain clean cuts and then sputtered with a thin layer of Au using a Leica EM ACE200 sputterer to assure good conductivity. Using a Zeiss LSM 800 microscope, transmitted-light images in

Formation of nanoflowers: Au and Ni silicide cores surrounded by SiO_x branches

• Feitao Li,
• Siyao Wan,
• Dong Wang and
• Peter Schaaf

Beilstein J. Nanotechnol. 2023, 14, 133–140, doi:10.3762/bjnano.14.14

• annealed at 1050 °C was named 15Au5Ni. The morphology was imaged by optical microscopy (OM, Zeiss Axiotech) and high-resolution scanning electron microscopy (HR-SEM, Hitachi S-4800) equipped with energy-dispersive X-ray spectroscopy (EDS, Thermo Scientific). The SEM images were recorded by using mixed

Combining physical vapor deposition structuration with dealloying for the creation of a highly efficient SERS platform

• Adrien Chauvin,
• Walter Puglisi,
• Damien Thiry,
• Cristina Satriano,
• Rony Snyders and
• Carla Bittencourt

Beilstein J. Nanotechnol. 2023, 14, 83–94, doi:10.3762/bjnano.14.10

• to the alloy thin film. Three different silver compositions were selected, namely 18, 30, and 36 atom %, and characterized by SEM/energy-dispersive X-ray spectroscopy (EDX). Figure 1 displays the SEM micrograph of the as-deposited thin films. The thin films exhibit a columnar morphology (see the

In search of cytotoxic selectivity on cancer cells with biogenically synthesized Ag/AgCl nanoparticles

• Mitzi J. Ramírez-Hernández,
• Mario Valera-Zaragoza,
• Omar Viñas-Bravo,
• Ariana A. Huerta-Heredia,
• Miguel A. Peña-Rico,
• Erick A. Juarez-Arellano,
• David Paniagua-Vega,
• Eduardo Ramírez-Vargas and
• Saúl Sánchez-Valdes

Beilstein J. Nanotechnol. 2022, 13, 1505–1519, doi:10.3762/bjnano.13.124

• -dispersive X-ray spectroscopy (EDX), and transmission electron microscopy (TEM) techniques were used to characterize nanoparticle development. The breast cancer cell line MCF-7 was used as a test model to study the cytotoxic behavior of Ag/AgCl nanoparticles and, as a counterpart, the nanoparticles were also

Rapid and sensitive detection of box turtles using an electrochemical DNA biosensor based on a gold/graphene nanocomposite

• Abu Hashem,
• M. A. Motalib Hossain,
• Ab Rahman Marlinda,
• Mohammad Al Mamun,
• Khanom Simarani and
• Mohd Rafie Johan

Beilstein J. Nanotechnol. 2022, 13, 1458–1472, doi:10.3762/bjnano.13.120

• with graphene. The spectrum of Gr in Figure 2c obtained by energy dispersive X-ray spectroscopy (EDX) clearly demonstrates the presence of a high amount of carbon with a minimum amount of oxygen, indicating the purity of Gr. Figure 2d clearly shows the presence of carbon, oxygen, and AuNPs in the

Enhanced electronic transport properties of Te roll-like nanostructures

• E. R. Viana,
• N. Cifuentes and
• J. C. González

Beilstein J. Nanotechnol. 2022, 13, 1284–1291, doi:10.3762/bjnano.13.106

• under mild conditions. A large quantity of these polycrystalline nanostructures with a diameter between 100 and 900 nm and a wall thickness around 50 nm were synthesized and characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), transmission electron microscopy

Effects of focused electron beam irradiation parameters on direct nanostructure formation on Ag surfaces

• Jānis Sniķeris,
• Vjačeslavs Gerbreders,
• Andrejs Bulanovs and
• Ēriks Sļedevskis

Beilstein J. Nanotechnol. 2022, 13, 1004–1010, doi:10.3762/bjnano.13.87

• material greatly affects the growth rate of the nanowires, with the Cu surface providing the fastest growth. Energy-dispersive X-ray spectroscopy (EDX) revealed the presence of both carbon and substrate materials in the nanowires. The effect of substrate material on nanowire growth rate could be attributed

Temperature and chemical effects on the interfacial energy between a Ga–In–Sn eutectic liquid alloy and nanoscopic asperities

• Yujin Han,
• Pierre-Marie Thebault,
• Corentin Audes,
• Xuelin Wang,
• Haiwoong Park,
• Jian-Zhong Jiang and
• Arnaud Caron

Beilstein J. Nanotechnol. 2022, 13, 817–827, doi:10.3762/bjnano.13.72

• liquid sample by fitting the function to our experimental data. The chemical composition of the eutectic Ga–In–Sn liquid alloy sample was determined by photoelectronic X-ray spectroscopy (XPS) before and after heating in air at 100 °C for 3 h. The spectrograms were recorded with a K-alpha+ XPS system

Nanoarchitectonics of the cathode to improve the reversibility of Li–O₂ batteries

• Hien Thi Thu Pham,
• Jonghyeok Yun,
• So Yeun Kim,
• Sang A Han,
• Jung Ho Kim,
• Jong-Won Lee and
• Min-Sik Park

Beilstein J. Nanotechnol. 2022, 13, 689–698, doi:10.3762/bjnano.13.61

• , and Zn1Co4 particles grown on CNT frameworks, respectively. Field-emission scanning electron microscopy (FESEM) observations confirmed that abundant rhombic dodecahedral ZnxCoy particles with different Zn/Co ratios were successfully integrated into the CNTs. Corresponding energy-dispersive X-ray

• spectroscopy (EDS) elemental mapping results (Supporting Information File 1, Figure S1) confirm that Zn and Co were uniformly distributed inside the as-grown ZnxCoy particles. We also found that the size of the ZnxCoy particles was decreased by increasing the ratio of Zn/Co during the synthesis due to the

Sodium doping in brookite TiO₂ enhances its photocatalytic activity

• Boxiang Zhuang,
• Honglong Shi,
• Honglei Zhang and
• Zeqian Zhang

Beilstein J. Nanotechnol. 2022, 13, 599–609, doi:10.3762/bjnano.13.52

• ). (1) Brookite—platy grains. Energy-dispersive X-ray spectroscopy (EDX) results of platy grains (Figure 4b) indicate that Na can be well identified besides Ti and O (note that the characteristic peak of C comes from the carbon conducting resin, Al from the sample holder, and Si from the silicon wafer

Sputtering onto liquids: a critical review

• Anastasiya Sergievskaya,
• Adrien Chauvin and
• Stephanos Konstantinidis

Beilstein J. Nanotechnol. 2022, 13, 10–53, doi:10.3762/bjnano.13.2

• energy-dispersive X-ray spectroscopy (S(T)EM-EDS). Typical examples of the formation of compositional gradients on coated surfaces can be found, for example, in [54][55]. Further control on film chemistry is obtained through reactive (magnetron) sputtering. In this case, the metallic target is sputtered

Enhancement of the piezoelectric coefficient in PVDF-TrFe/CoFe₂O₄ nanocomposites through DC magnetic poling

• Marco Fortunato,
• Alessio Tamburrano,
• Maria Paola Bracciale,
• Maria Laura Santarelli and
• Maria Sabrina Sarto

Beilstein J. Nanotechnol. 2021, 12, 1262–1270, doi:10.3762/bjnano.12.93

•  6b,c shows the aggregation of CoFe2O4 nanoparticles in some areas, in analogy with what has been reported in [25]. The formation of aggregates was confirmed by energy-dispersive X-ray spectroscopy (EDX). In correspondence with the agglomeration we observed a higher intensity of the O, Fe, and Co

Morphology-driven gas sensing by fabricated fractals: A review

• Vishal Kamathe and
• Rupali Nagar

Beilstein J. Nanotechnol. 2021, 12, 1187–1208, doi:10.3762/bjnano.12.88

• electrode resulting in a sensor prototype and were later used for UV-assisted acetone sensing. Figure 12a and Figure 12b show SEM images of top-view morphology and thickness of the sample at low and high magnifications, respectively. Figure 12c shows an energy-dispersive X-ray spectroscopy (EDS) mapping of

The effect of cobalt on morphology, structure, and ORR activity of electrospun carbon fibre mats in aqueous alkaline environments

• Markus Gehring,
• Tobias Kutsch,
• Osmane Camara,
• Alexandre Merlen,
• Hermann Tempel,
• Hans Kungl and
• Rüdiger-A. Eichel

Beilstein J. Nanotechnol. 2021, 12, 1173–1186, doi:10.3762/bjnano.12.87

• electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, elemental analysis, and inductively coupled plasma optical emission spectrometry (ICP-OES). In addition, the fibres were analysed in terms of their